depot/third_party/nixpkgs/nixos/modules/config/zram.nix

205 lines
6.6 KiB
Nix
Raw Normal View History

{ config, lib, pkgs, ... }:
with lib;
let
cfg = config.zramSwap;
# don't set swapDevices as mkDefault, so we can detect user had read our warning
# (see below) and made an action (or not)
devicesCount = if cfg.swapDevices != null then cfg.swapDevices else cfg.numDevices;
devices = map (nr: "zram${toString nr}") (range 0 (devicesCount - 1));
modprobe = "${pkgs.kmod}/bin/modprobe";
warnings =
assert cfg.swapDevices != null -> cfg.numDevices >= cfg.swapDevices;
flatten [
(optional (cfg.numDevices > 1 && cfg.swapDevices == null) ''
Using several small zram devices as swap is no better than using one large.
Set either zramSwap.numDevices = 1 or explicitly set zramSwap.swapDevices.
Previously multiple zram devices were used to enable multithreaded
compression. Linux supports multithreaded compression for 1 device
since 3.15. See https://lkml.org/lkml/2014/2/28/404 for details.
'')
];
in
{
###### interface
options = {
zramSwap = {
enable = mkOption {
default = false;
type = types.bool;
description = lib.mdDoc ''
Enable in-memory compressed devices and swap space provided by the zram
kernel module.
See [
https://www.kernel.org/doc/Documentation/blockdev/zram.txt
](https://www.kernel.org/doc/Documentation/blockdev/zram.txt).
'';
};
numDevices = mkOption {
default = 1;
type = types.int;
description = lib.mdDoc ''
Number of zram devices to create. See also
`zramSwap.swapDevices`
'';
};
swapDevices = mkOption {
default = null;
example = 1;
type = with types; nullOr int;
description = lib.mdDoc ''
Number of zram devices to be used as swap. Must be
`<= zramSwap.numDevices`.
Default is same as `zramSwap.numDevices`, recommended is 1.
'';
};
memoryPercent = mkOption {
default = 50;
type = types.int;
description = lib.mdDoc ''
Maximum total amount of memory that can be stored in the zram swap devices
(as a percentage of your total memory). Defaults to 1/2 of your total
RAM. Run `zramctl` to check how good memory is compressed.
This doesn't define how much memory will be used by the zram swap devices.
'';
};
memoryMax = mkOption {
default = null;
type = with types; nullOr int;
description = lib.mdDoc ''
Maximum total amount of memory (in bytes) that can be stored in the zram
swap devices.
This doesn't define how much memory will be used by the zram swap devices.
'';
};
priority = mkOption {
default = 5;
type = types.int;
description = lib.mdDoc ''
Priority of the zram swap devices. It should be a number higher than
the priority of your disk-based swap devices (so that the system will
fill the zram swap devices before falling back to disk swap).
'';
};
algorithm = mkOption {
default = "zstd";
example = "lz4";
type = with types; either (enum [ "lzo" "lz4" "zstd" ]) str;
description = lib.mdDoc ''
Compression algorithm. `lzo` has good compression,
but is slow. `lz4` has bad compression, but is fast.
`zstd` is both good compression and fast, but requires newer kernel.
You can check what other algorithms are supported by your zram device with
{command}`cat /sys/class/block/zram*/comp_algorithm`
'';
};
};
};
config = mkIf cfg.enable {
inherit warnings;
system.requiredKernelConfig = with config.lib.kernelConfig; [
(isModule "ZRAM")
];
# Disabling this for the moment, as it would create and mkswap devices twice,
# once in stage 2 boot, and again when the zram-reloader service starts.
# boot.kernelModules = [ "zram" ];
boot.extraModprobeConfig = ''
options zram num_devices=${toString cfg.numDevices}
'';
services.udev.extraRules = ''
KERNEL=="zram[0-9]*", ENV{SYSTEMD_WANTS}="zram-init-%k.service", TAG+="systemd"
'';
systemd.services =
let
createZramInitService = dev:
nameValuePair "zram-init-${dev}" {
description = "Init swap on zram-based device ${dev}";
after = [ "dev-${dev}.device" "zram-reloader.service" ];
requires = [ "dev-${dev}.device" "zram-reloader.service" ];
before = [ "dev-${dev}.swap" ];
requiredBy = [ "dev-${dev}.swap" ];
unitConfig.DefaultDependencies = false; # needed to prevent a cycle
serviceConfig = {
Type = "oneshot";
RemainAfterExit = true;
ExecStop = "${pkgs.runtimeShell} -c 'echo 1 > /sys/class/block/${dev}/reset'";
};
script = ''
set -euo pipefail
# Calculate memory to use for zram
mem=$(${pkgs.gawk}/bin/awk '/MemTotal: / {
value=int($2*${toString cfg.memoryPercent}/100.0/${toString devicesCount}*1024);
${lib.optionalString (cfg.memoryMax != null) ''
memory_max=int(${toString cfg.memoryMax}/${toString devicesCount});
if (value > memory_max) { value = memory_max }
''}
print value
}' /proc/meminfo)
${pkgs.util-linux}/sbin/zramctl --size $mem --algorithm ${cfg.algorithm} /dev/${dev}
${pkgs.util-linux}/sbin/mkswap /dev/${dev}
'';
restartIfChanged = false;
};
in listToAttrs ((map createZramInitService devices) ++ [(nameValuePair "zram-reloader"
{
description = "Reload zram kernel module when number of devices changes";
wants = [ "systemd-udevd.service" ];
after = [ "systemd-udevd.service" ];
unitConfig.DefaultDependencies = false; # needed to prevent a cycle
serviceConfig = {
Type = "oneshot";
RemainAfterExit = true;
ExecStartPre = "${modprobe} -r zram";
ExecStart = "${modprobe} zram";
ExecStop = "${modprobe} -r zram";
};
restartTriggers = [
cfg.numDevices
cfg.algorithm
cfg.memoryPercent
];
restartIfChanged = true;
})]);
swapDevices =
let
useZramSwap = dev:
{
device = "/dev/${dev}";
priority = cfg.priority;
};
in map useZramSwap devices;
};
}